Site Navigation

Choose Language

Introduction

Use this guide to replace a broken or noisy fan in your iMac Intel 27" Retina 5K Display, or simply remove it for cleaning.

Before beginning any work on your iMac: Unplug the computer and press and hold the power button for ten seconds to discharge the power supply's capacitors.

Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply.

Starting on the left of the display, near the power button, insert the iMac Opening Tool into the gap between the glass panel and the rear case.
  • Starting on the left of the display, near the power button, insert the iMac Opening Tool into the gap between the glass panel and the rear case.

  • The hub on the iMac Opening Tool will keep you from pushing the wheel in too far. If using a different tool, insert no more than 3/8" into the display. You risk severing antenna cables and causing serious damage.

Add Comment

Use the tool like a pizza cutter—roll it along through the gap, and it will cut the foam adhesive through the center.
  • Use the tool like a pizza cutter—roll it along through the gap, and it will cut the foam adhesive through the center.

  • Be sure to always push with the handle behind the cutting wheel. If you pull, the wheel might get pulled out of the handle.

  • Run the tool up along the left side of the display.

Add Comment

  • Continue wheeling the tool up around the top left corner.

Add Comment

  • Cut the adhesive along the top left of the display.

Add Comment

  • Continue along the top of the display.

  • You may want to run the tool back and forth through what you've already cut a few times, to ensure you get as much of the adhesive separated as possible.

Add Comment

  • Push the tool around the top right corner of the display.

Add Comment

  • Wheel the tool down along the right side of the display.

Add Comment

  • Finish pushing the opening tool to the bottom of the right side of the display.

  • At this point, you'll want to run the tool back around the entire display, to ensure you cut as much adhesive as possible.

Add Comment

  • While the opening tool did the lion's share of the work, the display will still be slightly adhered to the case. A plastic card will be necessary to free up the last of this adhesive.

  • Set the iMac face-up on a table.

  • Starting from the top right corner of the iMac, insert a plastic card between the display and frame.

    • Be careful not to insert it more than 3/8", or you may damage internal components.

Add Comment

  • Gently twist the plastic card to open the space between the display and frame.

  • Move slowly and be careful not to stress the display glass too much—you only need to make a gap of about 1/4".

Add Comment

  • Be sure to stop cutting before the iSight camera in this step, or you may damage it.

  • Slide the card toward the center of the display, to cut any remaining adhesive.

Add Comment

  • Put the card into the corner again and let it stay there to keep the adhesive from resettling.

Add Comment

  • Insert a second card into the gap between the display and frame in the top left corner.

Add Comment

  • Gently twist the card, slightly increasing the space between the display and frame.

  • As with the other side, move slowly to allow the adhesive to break, and be careful not to over-stress the display glass.

Add Comment

  • Slide the plastic card toward the center, again stopping just before the iSight camera.

Add Comment

  • Insert the card back into the top left corner.

Add Comment

  • Only lift the display a few inches—it is still attached to the iMac by data and power cables.

  • With the cards inserted as shown near the corners, gently twist the cards to increase the gap between display and case.

  • If there are any sections that seem to stick and won't separate, stop twisting and use one of the cards to cut the adhesive in the problem area.

  • Begin to lift the top of the display up from the frame.

Add Comment

  • While holding the display up with one hand, use the other to unplug the display power cable.

    • Lift the display up enough to have easy access to the connections, but not so much that you stretch the cables and stress their connections (about 8").

Add Comment

  • Flip up the metal retaining bracket on the display data cable.

  • Disconnect the display data cable.

    • This is a delicate connection that can easily be broken. Be sure to pull the display data cable connector straight out of its socket, toward the top of the iMac.

Add Comment

  • Lift the display up to a near-vertical position.

  • At this point there is still a strip of adhesive along the bottom of the display, that will hold the display to the frame like a hinge. You can loosen this adhesive by working the display up and down a few times.

Add Comment

  • If necessary, a plastic card can be used to cut any remaining sections of the bottom adhesive strip.

  • Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply (boxed in red).

Add Comment

  • Be very careful handling the display—it's big, heavy, and made of glass.

  • Lift the display up from the frame and remove it from the iMac.

  • It may be necessary to slowly lift from one side, to peel against the remaining adhesive.

Add Comment

  • With the hinge free to move, the iMac will be unbalanced and hard to work on. Repairs can be completed with the iMac laying down, but are faster and easier with an .

Add Comment

  • Use the tip of a spudger to disconnect the fan cable's connector from its socket on the logic board.

Add Comment

  • Peel the black tape connecting the fan to the exhaust duct back slightly.

  • Leave the tape in place on the exhaust duct, you only need to expose the join to free the fan.

Add Comment

  • Remove three 12.4 mm T10 screws securing the fan to the rear case.

Add Comment

  • Remove the fan from the iMac.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse and use our [invalid guide link] to reattach the display glass.

Dozuki System

Member since: 09/24/2009

276 Guides authored

0 Comments

Add Comment