Site Navigation

Choose Language

Introduction

Upgrade your hard drive for an increase in storage space.

Image 1/2: Stick a suction cup near each of the two top corners of the glass panel. Image 2/2: To attach the  we sell, first position the suction cup with the movable handle parallel to the face of the glass panel. While lightly holding the suction cup against the glass, raise the movable handle until it is parallel with the other handle.
  • Before beginning, unplug your iMac and lay it on a soft surface as shown.

  • Stick a suction cup near each of the two top corners of the glass panel.

  • To attach the we sell, first position the suction cup with the movable handle parallel to the face of the glass panel. While lightly holding the suction cup against the glass, raise the movable handle until it is parallel with the other handle.

  • If your suction cups refuse to stick, try cleaning both the glass panel and the suction cup with a mild solvent.

Add Comment

Image 1/2: Pull the glass panel away from the lower edge of the iMac and carefully set it aside. Image 2/2: During reinstallation, be sure to meticulously clean the inside of the glass panel and the face of the LCD as any dust or fingerprints trapped inside will be annoyingly visible when the machine is turned on.
  • Gently lift the glass panel perpendicular to the face of the LCD enough to clear the steel mounting pins attached along the underside of the top edge of the glass panel.

  • Pull the glass panel away from the lower edge of the iMac and carefully set it aside.

  • During reinstallation, be sure to meticulously clean the inside of the glass panel and the face of the LCD as any dust or fingerprints trapped inside will be annoyingly visible when the machine is turned on.

Add Comment

Image 1/3: The last two pictures are detail shots of each side of the display. Image 2/3: The last two pictures are detail shots of each side of the display. Image 3/3: The last two pictures are detail shots of each side of the display.
  • Remove the eight 8 mm T10 Torx screws securing the display to the outer case.

  • The last two pictures are detail shots of each side of the display.

Add Comment

Image 1/1: Do not lift it too much. There are several cables attaching the display to the logic board.
  • Slightly lift the top edge of the display out of the outer case.

  • Do not lift it too much. There are several cables attaching the display to the logic board.

Add Comment

Image 1/3: The vertical sync ribbon cable has a ZIF style end, but the socket has no lock or retaining flap. Simply pull the cable away from its socket toward the optical drive side of the iMac to disconnect it from the LED driver board. Image 2/3: The vertical sync ribbon cable has a ZIF style end, but the socket has no lock or retaining flap. Simply pull the cable away from its socket toward the optical drive side of the iMac to disconnect it from the LED driver board. Image 3/3: The vertical sync ribbon cable has a ZIF style end, but the socket has no lock or retaining flap. Simply pull the cable away from its socket toward the optical drive side of the iMac to disconnect it from the LED driver board.
  • Pull the vertical sync ribbon cable out of its socket on the LED driver board near the top left corner of your iMac.

  • The vertical sync ribbon cable has a ZIF style end, but the socket has no lock or retaining flap. Simply pull the cable away from its socket toward the optical drive side of the iMac to disconnect it from the LED driver board.

Add Comment

Image 1/3: Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac). Image 2/3: Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac). Image 3/3: Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac).
  • Rotate the display out of the outer case enough to disconnect the LED backlight power cable from the LED driver board.

  • Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac).

Add Comment

Image 1/1: Pull the display data cable connector away from its socket on the logic board.
  • Squeeze the two display data cable connector arms together to unlock it from its socket on the logic board.

  • Pull the display data cable connector away from its socket on the logic board.

Add Comment

Image 1/1:
  • Disconnect the LCD thermal sensor cable connector from its socket on the logic board.

Add Comment

Image 1/1:
  • Carefully pull the display toward the top edge of your iMac and lift it out of the outer case, minding any cables that may get caught.

Add Comment

Image 1/1: Disconnect the thermal sensor by pulling its connector away from the side of the hard drive.
  • Before disconnecting the thermal sensor cable, take note of its orientation. It is extremely important to reinstall the connector in the right orientation so the fans will not run at full speed.

  • Disconnect the thermal sensor by pulling its connector away from the side of the hard drive.

  • During reassembly, be sure that the thermal sensor connector is connected to set of pins closest to the SATA connectors.

Add Comment

Image 1/2: Use the flat end of a spudger to help disconnect the SATA power connector from the hard drive. Image 2/2: Use the flat end of a spudger to help disconnect the SATA power connector from the hard drive.
  • Disconnect the SATA data cable by pulling its connector away from the hard drive.

  • Use the flat end of a spudger to help disconnect the SATA power connector from the hard drive.

Add Comment

Image 1/1:
  • Remove the two 9 mm T10 Torx screws securing the upper hard drive bracket to the outer case.

Add Comment

Image 1/1:
  • Slightly rotate the hard drive out of the outer case and lift it up off its mounting pins toward the top edge of the iMac.

Add Comment

Image 1/1: Remove the upper bracket from the hard drive.
  • Remove the two T8 Torx screws securing the upper bracket to the hard drive.

  • Remove the upper bracket from the hard drive.

Add Comment

Image 1/1:
  • Remove the two T8 Torx pins from the other side of the hard drive.

Add Comment

Image 1/1: Don't forget to transfer this to your new hard drive.
  • Carefully peel off the piece of EMI foam attached to the front of the hard drive.

  • Don't forget to transfer this to your new hard drive.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Dozuki System

Member since: 09/24/2009

259 Guides authored

0 Comments

Add Comment