iMac Intel 24" EMC 2267 SSD Dual Drive Installation

Trade your optical drive for a second SSD.

There are many benefits to adding a second SSD to your iMac such as improved speeds, greater storage space, and less heartache when installing new software. Use this guide to install one using an optical bay hard drive enclosure.

Image #1

Step 1 Access Door  ¶ 

  • Lay your iMac front side down on a table with the lower edge facing yourself.

  • Loosen the single Phillips screw in the center of the access door.

  • This screw is captive in the access door.

  • Remove the access door from your iMac.

Image #1

Step 2 Glass Panel  ¶ 

  • The glass panel is fixed onto the front bezel with fourteen magnets around its perimeter.

  • Stick two suction cups to opposing corners of the glass panel.

  • To attach the we sell, first position the suction cup with the movable handle parallel to the face of the glass panel. While lightly holding the suction cup against the glass, raise the movable handle until it is parallel with the other handle.

  • If your suction cups refuse to stick, try cleaning both the glass panel and the suction cup with a mild solvent.

Image #1

Step 3  ¶ 

  • Gently pull the glass panel straight up off the iMac.

  • The glass panel has several positioning pins around its perimeter. To avoid shearing these pins off the glass panel, be sure to only pull straight up during removal.

  • Be meticulous about cleaning the LCD and the inside face of the glass panel before reinstallation, as any fingerprints or dust trapped inside will be annoyingly visible when the display is on.

Image #1

Step 4 Front Bezel  ¶ 

  • Remove the following 12 screws securing the front bezel to the rear case:

    • Eight 13 mm T8 Torx.

    • Four 25 mm T8 Torx.

  • On the 24" iMac Intel Model A1225, the bottom center two screws are long (26mm), four on sides (two left, two right) are medium (18mm), and the remaining 6 (four top, two bottom corners) are short (14mm).

Image #1

Step 5  ¶ 

  • The front bezel is still attached to the iMac by the microphone cable.

  • Gently lift the front bezel from its top edge off the rear case.

  • Once the top edge of the front bezel has cleared the rear case, rotate the front bezel toward the stand and lift it off the rear case.

  • Rotate the front bezel away from the rest of the device and lay it above the top edge of the iMac.

  • When reinstalling the front bezel, start at the lower edge and make sure it is flush with the rear case before lowering the top edge onto the iMac.

Image #1

Step 6  ¶ 

  • Disconnect the microphone cable connector, removing tape as necessary.

  • For the front bezel to sit properly, be sure to tuck the microphone cable and connector into the void next to the camera board.

Image #1

Step 7 Display Panel  ¶ 

  • Remove the two 5.3 mm T6 torx screws from the LCD connector.

  • Firmly grasp the pull tab on top of the connector and pull it straight up out of its port.

    • Make sure that you are pulling the tab and not the connector cable.

Image #1

Step 8  ¶ 

  • Place your hands on either side of the bottom of the display panel, and lift it up enough that you can reach the connectors inside.

    • Do not try to remove the display panel completely as it is still connected to the rest of the device.

  • While holding the display panel up with one hand, locate and remove the display thermal sensor cable from its connector.

Image #1

Step 9  ¶ 

  • While still holding the display panel up, use two fingers to firmly push down on the power supply cable connector from its socket.

Image #1

Step 10  ¶ 

  • Lift and remove the display panel from the device.

Image #1

Step 11 Optical Drive  ¶ 

  • Peel off the tape holding the optical drive in place.

  • Remove the two 7.1 mm T10 torx screws.

Image #1

Step 12  ¶ 

  • Firmly grab the optical drive connector and pull it straight out of the optical drive.

  • Remove the optical drive from the device.

Image #1

Step 13 Optical Drive Replacement  ¶ 

  • Remove the piece of foam tape covering the optical drive thermal sensor.

Image #1

Step 14  ¶ 

  • To remove the optical drive thermal sensor, use the tip of a spudger to lift the center finger of the thermal sensor bracket while applying slight tension to the thermal sensor cable.

  • If the thermal sensor is stuck to the optical drive, skip to the next step.

Image #1

Step 15  ¶ 

  • Use the flat end of a spudger to pry the optical drive thermal sensor bracket up off the adhesive securing it to the optical drive.

  • If the adhesive gets dirty or will not stick to your new optical drive, place some double-sided tape under the two semicircular ears of the thermal sensor bracket.

Image #1

Step 16  ¶ 

  • Use a spudger to remove the small piece of EMI foam from the bottom of the optical drive.

  • Don't forget to transfer this to your new drive.

Image #1

Step 17  ¶ 

  • Peel the EMI tape off the optical drive.

  • Don't forget to transfer this to your new optical drive.

Image #1

Step 18  ¶ 

  • Remove the two T10 Torx screws from both sides of the optical drive (four screws total).

Image #1

Step 19  ¶ 

  • Use the tip of a spudger to press each of the optical drive bracket tabs out of their slots on the bottom of the optical drive.

Image #1

Step 20  ¶ 

  • Rotate the optical drive bracket slightly away from the optical drive.

  • Pull the optical drive bracket away from the open end of the optical drive, minding any tabs that may get caught.

Image #1

Step 21 Optical Drive Enclosure Faceplate  ¶ 

  • Remove the three 3.0 mm Phillips #0 screws from the optical bay enclosure.

Image #1

Step 22  ¶ 

  • Starting from the left edge, gently pull open the optical bay enclosure.

  • Continue to pull open the two halves of the enclosure until they separate.

Image #1

Step 23  ¶ 

  • Remove the two 3.0 mm Phillips #0 screws securing the faceplate to the optical bay enclosure.

Image #1

Step 24  ¶ 

  • Lift the black plastic faceplate out of the optical bay enclosure.

    • You will no longer need the faceplate or the two Phillips screws that held it in place. Set those parts aside if you ever wish to put the faceplate back into the enclosure.

  • Reassemble the optical bay enclosure without the faceplate, reusing the original three 3.0 mm Phillips screws to keep it intact.

Image #1

Step 25 Dual Hard Drive  ¶ 

  • Remove the plastic positioner from the optical bay hard drive enclosure by pressing in on one of the clips on either side and lifting it up and out of the enclosure.

Image #1

Step 26  ¶ 

  • For 7 mm SSDs, you'll need to apply a spacer to ensure a good fit.

  • Peel the backings up off the adhesive strips mounted on the spacer.

  • Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes.

Image #1

Step 27  ¶ 

  • Make sure that the hard drive connectors are facing down before placing it into the enclosure.

  • Gently place the hard drive into the enclosure's hard drive slot.

  • While firmly holding the enclosure in place with one hand, use your other hard to press the hard drive into the enclosure connectors.

Image #1

Step 28  ¶ 

  • Once the hard drive is snug, reinsert the plastic positioner while holding the hard drive against the bottom of the enclosure.

  • Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the iMac Intel 24" EMC 2267 category page.

Comments Comments are onturn off

No comments.