Site Navigation

Choose Language

Introduction

When replacing your hard drive, you must transfer the Torx screws from the old drive to the new one.

Some drive bays have a height of 7 mm, while others have a height of 9.5 mm. Depending on the size of your drive bay, you may need to use a spacer to make your SSD fit properly.

Parts

Image 1/1:
  • Remove the eight 4 mm Phillips screws securing the lower case to the MacBook.

Add Comment

Image 1/3: Slightly lift the lower case near the vent opening. Image 2/3: Continue running your fingers between the lower and upper cases until the upper case pops off its retaining clips. Image 3/3: The location of these three clips is shown in the third picture.
  • The lower case is constructed of rubber-coated aluminum. Do not excessively bend the aluminum during removal, as any permanent deformation will cause tolerance issues after reassembly.

  • Slightly lift the lower case near the vent opening.

  • Continue running your fingers between the lower and upper cases until the upper case pops off its retaining clips.

  • The location of these three clips is shown in the third picture.

Add Comment

Image 1/1: Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.
  • For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.

  • Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.

  • It may be easier to use your fingernails to lift up on both sides of the connector.

Add Comment

Image 1/1: These screws are captive in the hard drive bracket.
  • Remove two 11 mm Phillips screws securing the hard drive bracket to the upper case.

  • These screws are captive in the hard drive bracket.

Add Comment

Image 1/1: When putting the bracket back after replacing the drive, it is easy to put in backwards. If it doesn't seat smoothly, then reverse it and try again.
  • Lift the retaining bracket out of the upper case.

  • When putting the bracket back after replacing the drive, it is easy to put in backwards. If it doesn't seat smoothly, then reverse it and try again.

Add Comment

Image 1/3: In some revisions of the MacBook A1342, the hard drive bracket may include two rubber brackets (as highlighted in the second picture.) The correct orientation of the rubber brackets is shown in the third picture. Image 2/3: In some revisions of the MacBook A1342, the hard drive bracket may include two rubber brackets (as highlighted in the second picture.) The correct orientation of the rubber brackets is shown in the third picture. Image 3/3: In some revisions of the MacBook A1342, the hard drive bracket may include two rubber brackets (as highlighted in the second picture.) The correct orientation of the rubber brackets is shown in the third picture.
  • Lift the hard drive by its pull tab and pull it away from the upper case, minding the cable still attaching it to the logic board.

  • In some revisions of the MacBook A1342, the hard drive bracket may include two rubber brackets (as highlighted in the second picture.) The correct orientation of the rubber brackets is shown in the third picture.

Add Comment

Image 1/2: Image 2/2:
  • Remove the hard drive cable by pulling its connector straight away from the hard drive.

Add Comment

Image 1/1: Transfer these screws to your new SSD.
  • Remove the four 6.0 mm T6 Torx hard drive retaining posts from the sides of the hard drive.

    • Transfer these screws to your new SSD.

  • If desired, transfer the pull tab over to your new hard drive.

Add Comment

Image 1/3: Peel the backings up off the adhesive strips mounted on the spacer. Image 2/3: Press the spacer onto the SSD as shown, proper orientation will ensure the spacer does not cover any screws or screw holes. Image 3/3: Press the spacer onto the SSD as shown, proper orientation will ensure the spacer does not cover any screws or screw holes.
  • For 7 mm SSDs, you'll need to apply a spacer to ensure a good fit.

  • Peel the backings up off the adhesive strips mounted on the spacer.

  • Press the spacer onto the SSD as shown, proper orientation will ensure the spacer does not cover any screws or screw holes.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Dozuki System

Member since: 09/24/2009

276 Guides authored

0 Comments

Add Comment