Site Navigation

Choose Language

Introduction

There are many benefits to adding a second hard drive to your laptop such as improved speeds, greater storage space, and less heartache when installing new software. Use this guide to install one using our optical bay hard drive enclosure.

Some drive bays have a height of 7 mm, while others have a height of 9.5 mm. Depending on the size of your drive bay, you may need to use a spacer to make your SSD fit properly.

Image 1/1:
  • Remove the eight 4 mm Phillips screws securing the lower case to the MacBook.

Add Comment

Image 1/3: Slightly lift the lower case near the vent opening. Image 2/3: Continue running your fingers between the lower and upper cases until the upper case pops off its retaining clips. Image 3/3: The location of these three clips is shown in the third picture.
  • The lower case is constructed of rubber-coated aluminum. Do not excessively bend the aluminum during removal, as any permanent deformation will cause tolerance issues after reassembly.

  • Slightly lift the lower case near the vent opening.

  • Continue running your fingers between the lower and upper cases until the upper case pops off its retaining clips.

  • The location of these three clips is shown in the third picture.

Add Comment

Image 1/1: Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.
  • For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.

  • Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.

  • It may be easier to use your fingernails to lift up on both sides of the connector.

Add Comment

Image 1/1: Two 10 mm T8 Torx
  • Remove the following screws from the optical drive side of the rear vent:

    • Two 10 mm T8 Torx

    • Two 5 mm Phillips

Add Comment

Image 1/1: Two 10 mm T8 Torx
  • Remove the following screws from the port side of rear vent:

    • Two 10 mm T8 Torx

    • Two 5 mm Phillips

Add Comment

Image 1/1:
  • Carefully lift the rear vent out of the upper case.

Add Comment

Image 1/1:
  • Remove the single 12 mm Phillips screw securing the top of the rear speaker housing to the upper case.

Add Comment

Image 1/1:
  • Remove the single 2.2 mm Phillips screw inserted horizontally into the side of the optical drive.

Add Comment

Image 1/1:
  • Use the flat end of a spudger to pry the AirPort/Bluetooth ribbon cable connector up off the logic board.

Add Comment

Image 1/1: Pry up underneath the wires.
  • Use the flat end of a spudger to pry the rear speaker connector up off the logic board.

  • Pry up underneath the wires.

  • This connector is very delicate and easily broken.

Add Comment

Image 1/1:
  • Carefully rotate the rear speaker assembly (with AirPort/Antenna cables still attached) out of the lower case.

Add Comment

Image 1/1:
  • Use the flat end of a spudger to pry the optical drive connector up off the logic board.

Add Comment

Image 1/1:
  • Remove the single 4.5 mm Phillips screw securing the optical drive bracket to the upper case near the fan.

Add Comment

Image 1/1:
  • Remove the two 2.5 mm Phillips screws securing the optical drive to the upper case near the optical drive opening.

Add Comment

Image 1/1:
  • Lift the optical drive near its connector and pull it away from the upper case to remove it from the computer.

Add Comment

Image 1/1:
  • Pull the optical drive cable connector away from the body of the optical drive.

Add Comment

Image 1/2: Image 2/2:
  • Remove the plastic positioner from the optical bay hard drive enclosure by pressing in on one of the clips on either side and lifting it up and out of the enclosure.

Add Comment

Image 1/3: Peel the backings up off the adhesive strips mounted on the spacer. Image 2/3: Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes. Image 3/3: Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes.
  • For 7 mm SSDs, you'll need to apply a spacer to ensure a good fit.

  • Peel the backings up off the adhesive strips mounted on the spacer.

  • Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes.

Add Comment

Image 1/3: Gently place the hard drive into the enclosure's hard drive slot. Image 2/3: While firmly holding the enclosure in place with one hand, use your other hard to press the hard drive into the enclosure connectors. Image 3/3: While firmly holding the enclosure in place with one hand, use your other hard to press the hard drive into the enclosure connectors.
  • Make sure that the hard drive connectors are facing down before placing it into the enclosure.

  • Gently place the hard drive into the enclosure's hard drive slot.

  • While firmly holding the enclosure in place with one hand, use your other hard to press the hard drive into the enclosure connectors.

Add Comment

Image 1/2: Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure. Image 2/2: Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.
  • Once the hard drive is snug, reinsert the plastic positioner while holding the hard drive against the bottom of the enclosure.

  • Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.

Add Comment

Image 1/2: Image 2/2:
  • Use two Phillips #1 screws to secure the drive to its enclosure.

Add Comment

Image 1/1: Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.
  • Attach the optical drive bracket to the new enclosure with two Phillips #0 screws.

  • Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Dozuki System

Member since: 09/24/2009

259 Guides authored

0 Comments

Add Comment