Site Navigation

Choose Language

Parts

Introduction

You can install hard drives up to 9.5mm thick.

Some drive bays have a height of 7 mm, while others have a height of 9.5 mm. Depending on the size of your drive bay, you may need to use a spacer to make your SSD fit properly.

Image 1/2: Image 2/2:
  • Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Add Comment

Image 1/2: Lift the memory door up enough to grip it and slide it toward you, pulling it away from the casing. Image 2/2: Lift the memory door up enough to grip it and slide it toward you, pulling it away from the casing.
  • Remove the three identical 2mm Phillips screws from the memory door.

  • Lift the memory door up enough to grip it and slide it toward you, pulling it away from the casing.

Add Comment

Image 1/1:
  • Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.

Add Comment

Image 1/1: Two 10 mm T6 Torx screws on either side of the RAM slot.
  • Remove the following 6 screws:

    • Two 10 mm T6 Torx screws on either side of the RAM slot.

    • Four 14.5 mm Phillips screws along the hinge.

Add Comment

Image 1/1:
  • Remove the four 3.2 mm Phillips screws on the port side of the computer.

Add Comment

Image 1/1:
  • Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.

Add Comment

Image 1/1:
  • Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.

Add Comment

Image 1/3: Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. Image 2/3: There are four plastic clips above the DVD slot, and another above and to the left of the IR sensor.  These clips can be very difficult to disengage without prying.  They can also be difficult to re-engage during reassembly. Image 3/3: There are four plastic clips above the DVD slot, and another above and to the left of the IR sensor.  These clips can be very difficult to disengage without prying.  They can also be difficult to re-engage during reassembly.
  • Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.

  • Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.

  • There are four plastic clips above the DVD slot, and another above and to the left of the IR sensor. These clips can be very difficult to disengage without prying. They can also be difficult to re-engage during reassembly.

Add Comment

Image 1/2: Note: It is possible to replace the hard drive without disconnecting the keyboard from the chassis, but it will need to be held upright to keep it out of the way, while still allowing you both hands to work on the drive removal. Be careful when removing the keyboard-trackpad ribbon cable to ensure that the rear of the upper case is disengaged from the area near the hinge. It is easy to accidentally bend the screw receivers on either side of the keyboard. Image 2/2: Remove the upper case.
  • Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.

  • Note: It is possible to replace the hard drive without disconnecting the keyboard from the chassis, but it will need to be held upright to keep it out of the way, while still allowing you both hands to work on the drive removal. Be careful when removing the keyboard-trackpad ribbon cable to ensure that the rear of the upper case is disengaged from the area near the hinge. It is easy to accidentally bend the screw receivers on either side of the keyboard.

    • Remove the upper case.

Add Comment

Image 1/2: Remove tape as necessary and use a spudger (or carefully push a credit card under the tape) to carefully loosen the adhesive securing the sleep light and IR sensor connectors to the top of the hard drive. Image 2/2: Remove tape as necessary and use a spudger (or carefully push a credit card under the tape) to carefully loosen the adhesive securing the sleep light and IR sensor connectors to the top of the hard drive.
  • Disconnect the orange hard drive ribbon cable from the logic board.

  • Remove tape as necessary and use a spudger (or carefully push a credit card under the tape) to carefully loosen the adhesive securing the sleep light and IR sensor connectors to the top of the hard drive.

Add Comment

Image 1/3: Lift the hard drive retaining bracket up and out of the computer. Image 2/3: Lift up the hard drive with one hand and use your other hand to disconnect the hard drive cable. Image 3/3: Lift up the hard drive with one hand and use your other hand to disconnect the hard drive cable.
  • Remove the two 8.2 mm T6 Torx screws securing the hard drive retaining bracket to the lower case.

  • Lift the hard drive retaining bracket up and out of the computer.

  • Lift up the hard drive with one hand and use your other hand to disconnect the hard drive cable.

Add Comment

Image 1/1: Transfer these screws to your new SSD.
  • Remove the two silver T6 6 mm Torx screws from the left side of the hard drive.

    • Transfer these screws to your new SSD.

Add Comment

Image 1/1:
  • Remove the two black T6 Torx screws and white rubber bumpers from the right side of the hard drive.

Add Comment

Image 1/3: Peel the backings up off the adhesive strips mounted on the spacer. Image 2/3: Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes. Image 3/3: Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes.
  • For 7 mm SSDs, you'll need to apply a spacer to ensure a good fit.

  • Peel the backings up off the adhesive strips mounted on the spacer.

  • Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Dozuki System

Member since: 09/24/2009

276 Guides authored

0 Comments

Add Comment