Site Navigation

Choose Language

Tools

Parts

Introduction

There are many benefits to adding a second SSD to your laptop such as improved speeds, greater storage space, and less heartache when installing new software. Use this guide to install one using an optical bay hard drive enclosure.

Some drive bays have a height of 7 mm, while others have a height of 9.5 mm. Depending on the size of your drive bay, you may need to use a spacer to make your SSD fit properly.

Image 1/1: Seven 3 mm Phillips screws.
  • Remove the following 10 screws securing the lower case to the MacBook Pro 13" Unibody:

    • Seven 3 mm Phillips screws.

    • Three 13.5 mm Phillips screws.

Add Comment

Image 1/1:
  • Slightly lift the lower case and push it toward the rear of the computer to free the mounting tabs.

Add Comment

Image 1/1: Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.
  • For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.

  • Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.

Add Comment

Image 1/1: Pry up from beneath the wires.
  • Using the flat end of a spudger, pry the right speaker/subwoofer cable connector straight up off the logic board. Be careful not to lift the socket. Pull the connector toward the optical drive.

  • Pry up from beneath the wires.

Add Comment

Image 1/1: Pull the camera cable connector toward the optical drive to disconnect it from the logic board.
  • It will be necessary to slide the small clear plastic cable retainer (boxed in red) glued to the logic board out of the way before disconnecting the camera cable. Be careful not to break any components off the board as you slide it away from the camera cable connector.

  • Pull the camera cable connector toward the optical drive to disconnect it from the logic board.

  • This socket is metal and easily bent. Be sure to align the connector with its socket on the logic board before mating the two pieces.

Add Comment

Image 1/1:
  • Use the flat end of a spudger to pry the optical drive connector straight up off the logic board.

Add Comment

Image 1/1:
  • Use the flat end of a spudger to pry the hard drive connector straight up off the logic board.

Add Comment

Image 1/1: The longer of the two screws is on the right.
  • Remove the two Phillips screws securing the subwoofer to the upper case.

  • The longer of the two screws is on the right.

Add Comment

Image 1/2: Lift the subwoofer off the optical drive, and set it above the computer. Image 2/2: Lift the subwoofer off the optical drive, and set it above the computer.
  • The subwoofer is still connected to the right speaker, so don't completely remove it just yet.

  • Lift the subwoofer off the optical drive, and set it above the computer.

Add Comment

Image 1/2: The right screw may remain captive in the camera cable. Image 2/2: Lift the camera cable bracket out of the upper case.
  • Remove the two Phillips screws securing the camera cable bracket to the upper case.

  • The right screw may remain captive in the camera cable.

  • Lift the camera cable bracket out of the upper case.

Add Comment

Image 1/2: Lift the optical drive from its right edge and pull it out of the computer. Image 2/2: Lift the optical drive from its right edge and pull it out of the computer.
  • Remove the three 2.5 mm Phillips screws securing the optical drive to the upper case.

  • Lift the optical drive from its right edge and pull it out of the computer.

Add Comment

Image 1/1: This connector is particularly deep, so be sure to pull away from the drive at the center of the connector.
  • Remove the optical drive cable by pulling it straight away from the optical drive.

  • This connector is particularly deep, so be sure to pull away from the drive at the center of the connector.

Add Comment

Image 1/2: Image 2/2:
  • Remove the plastic positioner from the optical bay hard drive enclosure by pressing in on one of the clips on either side and lifting it up and out of the enclosure.

Add Comment

Image 1/3: Peel the backings up off the adhesive strips mounted on the spacer. Image 2/3: Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes. Image 3/3: Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes.
  • For 7 mm SSDs, you'll need to apply a spacer to ensure a good fit.

  • Peel the backings up off the adhesive strips mounted on the spacer.

  • Press the spacer onto the SSD as shown; proper orientation will ensure the spacer does not cover any screws or screw holes.

Add Comment

Image 1/3: Gently place the hard drive into the enclosure's hard drive slot. Image 2/3: While firmly holding the enclosure in place with one hand, use your other hard to press the hard drive into the enclosure connectors. Image 3/3: While firmly holding the enclosure in place with one hand, use your other hard to press the hard drive into the enclosure connectors.
  • Make sure that the hard drive connectors are facing down before placing it into the enclosure.

  • Gently place the hard drive into the enclosure's hard drive slot.

  • While firmly holding the enclosure in place with one hand, use your other hard to press the hard drive into the enclosure connectors.

Add Comment

Image 1/2: Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure. Image 2/2: Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.
  • Once the hard drive is snug, reinsert the plastic positioner while holding the hard drive against the bottom of the enclosure.

  • Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.

Add Comment

Image 1/2: Image 2/2:
  • Use two Phillips #1 screws to secure the drive to its enclosure.

Add Comment

Image 1/1: Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.
  • Attach the optical drive bracket to the new enclosure with two Phillips #0 screws.

  • Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Dozuki System

Member since: 09/24/2009

276 Guides authored

0 Comments

Add Comment